ywb1031 发表于 2010-7-17 10:58:00

为什么BSD6下正常,升级到BSD8后PA就不稳定,会断网?

原来BSD6一切正常,只是好久没能升级特征库了,不得已来升级BSD8和10.01,
却在正常使用十几至几十分钟后网络中断!管理口正常访问!
换成10.07也是同样.网卡是双口的82559,难道是对网卡支持不好?
谁可以解释一下?在不换硬件的前提下有什么解决办法?

ywb1031 发表于 2010-7-19 07:56:40

把什么用不到的驱动都关掉,重新编译内核,还是一样,
没流量的情况下开一个晚上都正常,有点流量以后就会断网!
为什么?管理员呢?

panabit 发表于 2010-7-19 08:31:01

原帖由 ywb1031 于 2010-7-19 07:56 发表 http://www.panabit.com/forum/images/common/back.gif
把什么用不到的驱动都关掉,重新编译内核,还是一样,
没流量的情况下开一个晚上都正常,有点流量以后就会断网!
为什么?管理员呢?

驱动都是BSD带的，没有关掉什么驱动。

ywb1031 发表于 2010-7-19 08:40:28

启动程序的时候发现这些消息,不知道和问题有没有关系?

Load module "pci" ......
      fxp1@bus2:5:0: 0x8086:0x1229
      fxp3@bus3:5:0: 0x8086:0x1229
Load module "thread" ......
Load module "cmds" ......
Load module "dma" ......
This is standard version, no PANAOS DMA supported!
Load module "mgmt" ......
Load module "mbuf" ......
Load module "intf" ......
Load module "bsd" ......
network is started!
      interface fxp1 attached, mac address 00:02:A5:5C:34:B3
      bring interface fxp1 up
      interface fxp3 attached, mac address 00:02:A5:2C:AF:45
      bring interface fxp3 up
Starting ipe_httpd ......
Load module "ipe" ......
Load module "axpdef" ......
ipe_httpd is started!
Load module "watcher" ......
Load module "tbucket" ......
/usr/panabit/bin/ipe_httpd: started as root without requesting chroot(), warning only
ipe_monitor is started!
Load module "key" ......
data monitor is started!
Load module "keytable" ......
Load module "axpdesc" ......
Load module "flow" ......
Load module "cmds" ......
Load module "node" ......
Load module "dbf" ......
Load module "cmds" ......
Load module "xping" ......
dbf_minit: logpath is '/usr/panalog', internal is 360
Load module "thread" ......
dbf_load: newestime 1279498823, current time 1279499405
Load module "stat" ......
Load module "chart" ......
Load module "logger" ......
Load module "port" ......
port module initialzied, max port 65536
thr_stat_0 is running ......
Load module "axpgrp" ......
thr_stat_1 is running ......
Load module "protocol" ......
applog is running ......
Load module "appobj" ......
iplog is running ......
Load module "localip" ......
Load module "iptable" ......
cpuset: Load module "vlink" ......
setaffinityLoad module "nat" ......
: Load module "policy_scheduler" ......
Operation not supported
Load module "pre-config" ......
Load module "logger" ......
cpuset: Load module "flow" ......
setaffinity   share CPU with control plane!
: Load module "config" ......
Operation not supported
1: interface not exist
Load module "josdbf" ......
cpuset: panaos startup!
setaffinityxping is running ......
: logger is running ......
Operation not supported
flow is running ......
cpuset: setaffinity: Operation not supported
root@P8cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported
cpuset: setaffinity: Operation not supported

ywb1031 发表于 2010-7-26 15:58:32

重装了FREEBSD8.1RC2 再装10.07,再全手工新建规则，发现不会断网了，
原来是从备份的规则导入的，是什么原因？难道是导入的问题？还是FREEBSD8的问题？
页: [1]
查看完整版本: 为什么BSD6下正常,升级到BSD8后PA就不稳定,会断网?